Author Topic: Inspire Clone Build instructions  (Read 46954 times)

Offline jacpresta

  • Drinks Maker
  • *
  • Posts: 22
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #30 on: August 17, 2015, 07:53:28 AM »
Tanks rcfiddy1.
I also have problems with the accelerometer calibration and I suppose my Pixhawk clone from Bangood is defective.
I've order a Naza lite and FrSky receiver and I hope it will be better.

Offline CdRsKuLL

  • Administrator
  • Master Builder
  • *****
  • Posts: 817
  • Karma: +47/-3
  • The fat dude
    • View Profile
Re: Inspire Clone Build instructions
« Reply #31 on: August 17, 2015, 08:00:56 AM »
Is this where you do the naza dance?  I did mine and twirled round and it set fine but then I had trouble flipping it over, is this what you mean by vertical? If so, then it might need a bit of copper underneath the gps puk if that's where the compass is located.  I believe copper makes a good shield and should help. You can buy thin sheets of copper from ebay so wil order some and give it a try.
If you use any of my designs and can afford to donate to help pay for this site and the filament, or just buy me a beer then please click on the link below, enter an amount and donate what you want.


Offline jacpresta

  • Drinks Maker
  • *
  • Posts: 22
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #32 on: August 17, 2015, 08:28:03 AM »
Yes it is.
I have already "accelerometer calibration failled".
My NeoM8 gps/compas is directly fixed on the top of my Inspire frame without any protection.
I'll try to put a copper sheet and start again the tests;

Offline CdRsKuLL

  • Administrator
  • Master Builder
  • *****
  • Posts: 817
  • Karma: +47/-3
  • The fat dude
    • View Profile
Re: Inspire Clone Build instructions
« Reply #33 on: August 17, 2015, 08:34:36 AM »
Do you have some to try? I've ordered some sticky copper EMI shield tape used for an electric guitar but will have to wait a couple of weeks as I'm off on holiday tomorrow for 2 weeks.
If you use any of my designs and can afford to donate to help pay for this site and the filament, or just buy me a beer then please click on the link below, enter an amount and donate what you want.


Offline jacpresta

  • Drinks Maker
  • *
  • Posts: 22
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #34 on: August 17, 2015, 08:47:48 AM »
I have this part http://www.studiosport.fr/cache-gps-inferieur-dji-inspire-1-p-5032.html
It seems to be a metallic part and I hope it 'll do the job.
Thanks for your help.Have a good holiday

Offline rcfiddy1

  • Designer
  • ***
  • Posts: 161
  • Karma: +5/-1
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #35 on: August 26, 2015, 09:50:48 PM »
I have copper shielding tape from my guitar builds so I will give it a few pieces. I ordered a NAza V2 for this.

Offline jacpresta

  • Drinks Maker
  • *
  • Posts: 22
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #36 on: August 27, 2015, 07:25:30 AM »
I have just received my Banggood Naza V1 and I will start again the tests.
Later I would make an upgrade V1/V2 with this software http://naza-upgrade.com/
Thank you for the offer but I have copper.

Offline Eltrocha

  • Junior Designer
  • **
  • Posts: 58
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #37 on: August 29, 2015, 01:54:00 PM »
Steve as much as I've tried to follow the build diaries u don't really know where to start. I have almost every piece printed and all materials. I'm just missing how to start.

Thanks

Offline Eltrocha

  • Junior Designer
  • **
  • Posts: 58
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #38 on: August 29, 2015, 06:26:42 PM »
Okay. That helped a lot more. The rest of the parts are snap in or normal M3 screws with nuts will do?

Offline rcfiddy1

  • Designer
  • ***
  • Posts: 161
  • Karma: +5/-1
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #39 on: August 29, 2015, 06:39:31 PM »
YEs. I will update as I create the pics.

Offline eaglesight

  • Drinks Maker
  • *
  • Posts: 46
  • Karma: +0/-2
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #40 on: August 30, 2015, 05:57:26 PM »
rcfiddy1




sent a pm

Offline eaglesight

  • Drinks Maker
  • *
  • Posts: 46
  • Karma: +0/-2
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #41 on: August 30, 2015, 08:06:57 PM »
arm6 picture i see 2 leg links in blue has it been revised

Offline eaglesight

  • Drinks Maker
  • *
  • Posts: 46
  • Karma: +0/-2
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #42 on: August 30, 2015, 08:20:28 PM »
getting confused maybe this will help, I'm going cdrskull inspire from thingiverse   http://www.thingiverse.com/thing:915443/#files. can you just tell me all that i need for bearings/bushings and carbon fiber tube size/lenth and how many, I'm being a pain in _ss guess reading to much on post. Im printing everything on the link above in org files. I'm 3/4 done printing now. sorry for being an _ss.

Offline CdRsKuLL

  • Administrator
  • Master Builder
  • *****
  • Posts: 817
  • Karma: +47/-3
  • The fat dude
    • View Profile
Re: Inspire Clone Build instructions
« Reply #43 on: August 30, 2015, 08:22:19 PM »
Grab the latest stl pack from the download section on here, it has some updated parts.
If you use any of my designs and can afford to donate to help pay for this site and the filament, or just buy me a beer then please click on the link below, enter an amount and donate what you want.


Offline eaglesight

  • Drinks Maker
  • *
  • Posts: 46
  • Karma: +0/-2
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #44 on: August 30, 2015, 08:29:14 PM »
I have it, just loaded 1 hr ago, but wasn't the original  with 16mm tubes, 8mm, 5mm carbon fiber tubes or am i mistaken. I need the correct bearing and carbon from you orig post on thigvirse since my arms are printed sorry for this. I'm gonna order the tubes and bearing ext and want to make sure i order the right stuff