Author Topic: Inspire Clone Build instructions  (Read 89567 times)

Offline eaglesight

  • Drinks Maker
  • *
  • Posts: 46
  • Karma: +0/-3
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #45 on: August 30, 2015, 09:43:40 PM »
Sorry I found your material list some how I have another list   I use the jr 9303 10 channel to you think when you set up gear channel and using the 360 servo  that your travel adjustment would be enough for travel. How much does the just meant move in one direction say at center point was thinking if you set up on your 3 way switch at center it might be enough throw tell me what you think I might just try it with a servo if I know the total lift and lower measurement in one direction

Offline CdRsKuLL

  • Administrator
  • Master Builder
  • *****
  • Posts: 839
  • Karma: +60/-5
  • The fat dude
    • View Profile
Re: Inspire Clone Build instructions
« Reply #46 on: August 30, 2015, 09:49:14 PM »
The 360 servo works differently to a normal one. It just keeps going round and round. I think it goes round about 4 times to fully lift the legs. The centre position just stops the servo it doesn't return it to a center point.
If you use any of my designs and can afford to donate to help pay for this site and the filament, or just buy me a beer then please click on the link below, enter an amount and donate what you want.


Offline eaglesight

  • Drinks Maker
  • *
  • Posts: 46
  • Karma: +0/-3
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #47 on: August 30, 2015, 09:55:00 PM »
I was just thinking if there was enough travel in the radio and sub trim to preset like my radio I have -+ 150 sub and travel

Offline eaglesight

  • Drinks Maker
  • *
  • Posts: 46
  • Karma: +0/-3
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #48 on: August 30, 2015, 10:02:25 PM »
That is starting from a center point for both ways. If not can you tell me how to wire in the switchs to servo I see the diagram but lost. Say better detail inside servo ( an actual pic)

Offline eaglesight

  • Drinks Maker
  • *
  • Posts: 46
  • Karma: +0/-3
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #49 on: August 31, 2015, 08:34:20 PM »
great job on the picture instructions well done.

Offline ulissessalvador

  • Drinks Maker
  • *
  • Posts: 5
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #50 on: September 21, 2015, 06:03:49 PM »
good afternoon no one has printed the nose and Top Cover dji Base inspire one?

Offline rcfiddy1

  • Designer
  • ***
  • Posts: 161
  • Karma: +5/-1
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #51 on: September 21, 2015, 07:25:58 PM »
Nobody has done it yet.

Offline ulissessalvador

  • Drinks Maker
  • *
  • Posts: 5
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #52 on: September 21, 2015, 07:39:58 PM »
and shame because along very way

Offline aussiemikey

  • Drinks Maker
  • *
  • Posts: 2
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #53 on: December 20, 2015, 06:19:09 AM »
Hey guys, for some reason I cannot open the part list file, each of the links will just open to www.ebay.com.  Can someone link a list in text form or actual ebay item number for the part list...thanks in advanced!!!

Offline Davis Patch

  • Drinks Maker
  • *
  • Posts: 1
  • Karma: +0/-0
  • young and retatred
    • View Profile
    • Casinority
Re: Inspire Clone Build instructions
« Reply #54 on: December 29, 2015, 12:50:28 PM »
this looks pretty sweet and i really want to try this asa i'll have a 3d
insipire is my next buy

Offline Inspire.clone

  • Junior Designer
  • **
  • Posts: 86
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #55 on: January 26, 2016, 12:51:49 AM »
this looks pretty sweet and i really want to try this asa i'll have a 3d


Hi Welcome


I can confirm it is a real joy to print and then construct.... Loads of help available..


Regards

Offline CdRsKuLL

  • Administrator
  • Master Builder
  • *****
  • Posts: 839
  • Karma: +60/-5
  • The fat dude
    • View Profile
Re: Inspire Clone Build instructions
« Reply #56 on: February 09, 2016, 07:36:24 AM »
I will be starting version 2 once I finish my other project...  But that's 6 months away.. So get printing :-)
If you use any of my designs and can afford to donate to help pay for this site and the filament, or just buy me a beer then please click on the link below, enter an amount and donate what you want.


Offline Inspire.clone

  • Junior Designer
  • **
  • Posts: 86
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #57 on: February 09, 2016, 10:25:30 AM »
I will be starting version 2 once I finish my other project...  But that's 6 months away.. So get printing :-)


Hi Steve


Care to give any insight into what version 2 may have had changed/adjusted?


Should be close to a maiden soon with my own.....




Offline CdRsKuLL

  • Administrator
  • Master Builder
  • *****
  • Posts: 839
  • Karma: +60/-5
  • The fat dude
    • View Profile
Re: Inspire Clone Build instructions
« Reply #58 on: February 09, 2016, 02:14:40 PM »
I'm thinking a complete redesign  really, all 3d printed with no DJI bits.. Also the main aim is to reduce the weight a bit. .. Maybe add some more LEDs, a standard fpv mini camera which can move up and down at the front.. Still using all the motors etc from before .. Might even have a go at printing the screw thread, will have to see. Need to finish my car first mind!
If you use any of my designs and can afford to donate to help pay for this site and the filament, or just buy me a beer then please click on the link below, enter an amount and donate what you want.


Offline Inspire.clone

  • Junior Designer
  • **
  • Posts: 86
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Build instructions
« Reply #59 on: February 09, 2016, 02:20:11 PM »
That sounds very interesting. I tried printing a screw rod. I found you need a very good filament cooling fan and a very well adjusted printer. I managed one of 70mm long but by then the filament as cooled too much .......


I was looking at using EMAX 4114 MT motors. Wi a total Thrust of 2350grams. But unfortunately they need a 6S lipo...... I am open to suggestions.


Do you have any guides to the Usual AUW ?


Regards S