Author Topic: Inspire Clone Electronics  (Read 59906 times)

Offline Bioethical

  • Global Moderator
  • Designer
  • *****
  • Posts: 226
  • Karma: +2/-0
  • "Patience is the mother of science"
    • View Profile
Re: Inspire Clone Electronics
« Reply #105 on: April 18, 2018, 10:28:59 PM »
zhadden1989,
Maybe this can help. I put the GPS there before the canopy (covers) existed
« Last Edit: April 18, 2018, 10:43:22 PM by Bioethical »

Offline zhadden1989

  • Drinks Maker
  • *
  • Posts: 8
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Electronics
« Reply #106 on: April 18, 2018, 10:50:28 PM »
yes that did thanks for that.


did you use the dji base plate or did you 3d print one?

Offline Bioethical

  • Global Moderator
  • Designer
  • *****
  • Posts: 226
  • Karma: +2/-0
  • "Patience is the mother of science"
    • View Profile
Re: Inspire Clone Electronics
« Reply #107 on: April 19, 2018, 02:16:40 AM »
If you mean the base plate for the GPS, I didn't. I affix it down there. Check the picture at the bottom.

Offline zhadden1989

  • Drinks Maker
  • *
  • Posts: 8
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Electronics
« Reply #108 on: April 21, 2018, 02:48:47 AM »
No I mean the very bottom plate to the drone

Offline Bioethical

  • Global Moderator
  • Designer
  • *****
  • Posts: 226
  • Karma: +2/-0
  • "Patience is the mother of science"
    • View Profile
Re: Inspire Clone Electronics
« Reply #109 on: April 21, 2018, 05:22:51 AM »
Actually, I wrongfully bought this canopy that a guy put on sale here which is against the rules of this site because all the design work made by Steven is free of charge but voluntary donations are accepted.
« Last Edit: April 21, 2018, 05:24:48 AM by Bioethical »

Offline CdRsKuLL

  • Administrator
  • Master Builder
  • *****
  • Posts: 817
  • Karma: +47/-3
  • The fat dude
    • View Profile
Re: Inspire Clone Electronics
« Reply #110 on: April 21, 2018, 12:10:50 PM »
Looking good :-)   I didn't mind you buying the canopy at all, looks good in fact. I just didn't really approve of the guy advertising it on here when all files should be free no matter who the author is. That was my original idea anyway. A lot of member including yourself have freely donated your time / designs and ideas which is what has made this forum a success and I'm very grateful for it :-)  I just wish I had some spare time to carry donating like. Hopefully, once my car is finished I can then crack on with a new design.
If you use any of my designs and can afford to donate to help pay for this site and the filament, or just buy me a beer then please click on the link below, enter an amount and donate what you want.


Offline zhadden1989

  • Drinks Maker
  • *
  • Posts: 8
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Electronics
« Reply #111 on: April 21, 2018, 01:18:00 PM »
Steve have you heard of anyone making a printed base plate?

Offline CdRsKuLL

  • Administrator
  • Master Builder
  • *****
  • Posts: 817
  • Karma: +47/-3
  • The fat dude
    • View Profile
Re: Inspire Clone Electronics
« Reply #112 on: April 21, 2018, 07:48:16 PM »
As in the bottom bit?  Sadly not I'm afraid. I would of thought that part would be printable mind, just need someone to model it up.
If you use any of my designs and can afford to donate to help pay for this site and the filament, or just buy me a beer then please click on the link below, enter an amount and donate what you want.


Offline zhadden1989

  • Drinks Maker
  • *
  • Posts: 8
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Electronics
« Reply #113 on: April 21, 2018, 08:53:28 PM »
If i had one i would model it for sure i might have to find wherebi can get one really cheap.

Offline zhadden1989

  • Drinks Maker
  • *
  • Posts: 8
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Electronics
« Reply #114 on: April 25, 2018, 01:51:30 AM »
how do you guys have your leds powered and set up with the arduino.

i was thinking about placing 2 leds epistar leds on the bottom of my copter as a steady flash but have a different flash when the arms in motion as we as have a really fast flash when the battery get below a set point, and also have 4 red led on the front and 4 green led on the back (2 on each side)as a constant on...... do you guys think that this is possible?

Offline Bioethical

  • Global Moderator
  • Designer
  • *****
  • Posts: 226
  • Karma: +2/-0
  • "Patience is the mother of science"
    • View Profile
Re: Inspire Clone Electronics
« Reply #115 on: April 25, 2018, 03:00:16 AM »
Once again my ugly diagram to the rescue. Connect the positive wires from the legs of the leds to the arduino card on the pins 9, 10, 11, and 12, as in the diagram. The negative leg of the leds can be connected to the negative cables of the ESCs. The arduino is programed to make the leds blink when the arms of the inspire are moving.

Offline svensoni08@gmail.com

  • Drinks Maker
  • *
  • Posts: 3
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Electronics
« Reply #116 on: May 31, 2018, 10:05:42 PM »
I am programming my arduino nano with this code but it's showing me
Wprogram.h error
So how can i fix this
Please help

Offline Bioethical

  • Global Moderator
  • Designer
  • *****
  • Posts: 226
  • Karma: +2/-0
  • "Patience is the mother of science"
    • View Profile
Re: Inspire Clone Electronics
« Reply #117 on: June 01, 2018, 02:47:24 AM »
Hello Svenson,
Welcome to the forum.
Your problem may be an error of procedure. Remember that you need to copy the code as it is in the gray area and then paste it on the sketch of the arduino platform. Then proceed to check "tools" before to upload it to your card.
Please read all the posts possible in the Electronics section.
Also, be patient. It'll work.

Vic