Author Topic: Inspire Clone Parts required  (Read 35175 times)

Offline fofomo

  • Drinks Maker
  • *
  • Posts: 1
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #30 on: March 13, 2016, 02:10:12 PM »
what is length of bolt and some screw?
i don`t know where to buy a ESC extention wire 4 metres. most shop have a 1m or mm


i am sorry i am not good at english

Offline Inspire.clone

  • Junior Designer
  • **
  • Posts: 86
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #31 on: March 28, 2016, 02:23:25 PM »
Post 1 of this thread contains the parts list.
buy 4x1m servo wire. You need too cut it anyway.


Regards

Offline mbaker335

  • Drinks Maker
  • *
  • Posts: 3
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #32 on: March 28, 2016, 03:53:09 PM »
"Post 1 of this thread contains the parts list." Except almost all the links in the spreadsheet are dead so effectivly there is little to no parts list anymore. It is possible to get some idea from other posts but it is a real slog. My build has stalled as I am not willing to spend on the more expensive items until I can get all the info on parts and build.

Offline mbaker335

  • Drinks Maker
  • *
  • Posts: 3
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #33 on: March 28, 2016, 06:10:08 PM »
I do not expect to be spoon fed but at least an idea of what was needed would be good. I enjoy making chinese valve amp kits. A pile of parts, an inside photo and smudged circuit diagram. Working out what goes where and at 350v is actually fun detective work. In the case of this clone what we have is no circuit diagram(ie exploded build diagram), no complete parts list and a few photographs where the important bits are covered up.


I guess the issue is I can build the high voltage valve amps because I built RF amps 30 years ago and have the experience to do so. A complete beginner would probably kill themselves. With a drone I am a complete beginner. I can do the electronics and have loads of ideas re more automation etc but a pile of weird shaped bits of plastic is a guessing job too far. Well done to those who have built these machines but I will stick to electronics for the time being. Which is a shame.

Offline berrylite

  • Drinks Maker
  • *
  • Posts: 2
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #34 on: May 29, 2016, 02:08:34 PM »
Various parts will be required to build the quadcopter. I've sourced these from different places and will most likely not be the cheapest so please shop around. If you find somewhere then please post for others. You will also need to extend some wires so soldering will be required.

I've put the list in an excel file and have most likely forgot something. No RC components other than the servo are included in this list.

You will require some original DJI parts.

DJI Inspire 1 Airframe Top Cover Part 31 - 16.00
DJI Inspire 1 Airframe Nose Part 32 - 12.00
DJI Inspire 1 Airframe Base Part 37 - 17.00

DJI Inspire 1 Airframe Arms Part 33 - 5.00

These can be purchased from eBay / Inspire part suppliers etc. The price is what I paid.

can i use these http://www.aliexpress.com/item/4-PCS-GARTT-ML3510-600KV-Brushless-RC-Motor-For-Multicopter-Quadcopter-Hexa/32358999002.html?spm=2114.40010208.4.32.oKP7dx

RC Components I've used
4 x EMAX 3510 600kv motors (suitable for 4s battery)
Naza M Lite (flashed to v2) with GPS
4 x simonK ESC 30amp
Turnigy 5000mAh 4S1P 14.8v 20C Hardcase Pack Lipo
4 x 1347 Gemfan props

More info to come....

Offline youchul

  • Drinks Maker
  • *
  • Posts: 1
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #35 on: July 06, 2016, 12:11:59 PM »
Broken ebay links....  :( 
Plz Can get anywhere?

Offline Chris23

  • Drinks Maker
  • *
  • Posts: 37
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #36 on: July 06, 2016, 12:23:46 PM »
They will broke again... Just google the parts or search them on ebay. It's done in 5 minutes.  ;)

Offline elbrujo

  • Drinks Maker
  • *
  • Posts: 1
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #37 on: October 01, 2016, 04:27:55 PM »
Can someone tell me what sizes they cut their carbon tubes for the arms and motor portions. I have already built one clone but this one is more like the inspire one so any help would be appreciated

Offline Chris23

  • Drinks Maker
  • *
  • Posts: 37
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #38 on: October 01, 2016, 04:35:44 PM »
Take a look at my build diary (the mate black one) there are all sizes listed.  ;)

Offline Gazzacapour1

  • Drinks Maker
  • *
  • Posts: 2
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #39 on: October 27, 2016, 06:07:33 PM »
Hi All,
Coming to this party very late by the look of it, but, I have only just found you. I currently fly my Tarot 650 Sport which I built from a kit and run with Pixhawk flight controller. Always loved the Inspire 1 but like most people can't afford to spend that sort of money on my hobby. I have donated and downloaded the v1.4 files and as I don't have access to 3d Printer I intend to try and find a printing company to provide the required parts.
Questions of which I am sure I will have many, start with
1. Can anyone recommend a possible company to print?
2. Does anyone know how much it is likely to cost to get printed?
3. Finally I see mention of parts list but can't find it on the site. I have all the electronics on my Tarot that I intend to switch over but need the list of screws etc.


Any help would be appreciated.


Thanks


Gary

Offline Chris23

  • Drinks Maker
  • *
  • Posts: 37
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #40 on: October 27, 2016, 08:15:10 PM »
Hi Gary,
In my opinion a company for printing makes no sense because the costs will be so high (here in Germany it is) you could buy your own. A list for the screws is not available but you can messure the needed length after printing your parts. Everything else you can read in my building diary.

Best regards

Chris

Offline Gazzacapour1

  • Drinks Maker
  • *
  • Posts: 2
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #41 on: October 30, 2016, 10:09:05 AM »
Thanks Chris I believe you are correct.Think this would be a step too far without the ability to reprint when needed.
looking into second hand DJI market.
thanks
Gary

Offline Chris23

  • Drinks Maker
  • *
  • Posts: 37
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #42 on: October 30, 2016, 07:31:50 PM »
Take a look at the CTC Dual Extruder. I got this for 350 and it is really good! I would buy it again if there would be enough space on my desk.

Offline airwolf09

  • Drinks Maker
  • *
  • Posts: 3
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Inspire Clone Parts required
« Reply #43 on: March 24, 2017, 02:08:25 AM »
the spreadsheet has broken link. instead of the link can we get the name of the part or picture so that i can google to find the part?
can someone post the part name please?

thanks,

Offline Bioethical

  • Global Moderator
  • Designer
  • *****
  • Posts: 226
  • Karma: +2/-0
  • "Patience is the mother of science"
    • View Profile
Re: Inspire Clone Parts required
« Reply #44 on: March 25, 2017, 08:11:08 PM »
Airwolf, please give me a clue of what you are looking for and I'll try to find it for you,