Author Topic: Mavic Clone STL Files Version 4.1 Naza  (Read 58718 times)

Offline jkaechler

  • Drinks Maker
  • *
  • Posts: 10
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic Clone STL Files Version 4.1 Naza
« Reply #150 on: February 02, 2018, 04:25:42 AM »
whether applicable in mavic clone, http://www.hobbywow.com/en-camera-gimbal-camera-for-c-fly-obtain-rc-quadcotper-obtain-05-p245120.htm

This would be awesome, if it can be operated by just applying power and maybe a pwm pitch control.  Is there any more information on this unit anywhere?

Offline skyman

  • Drinks Maker
  • *
  • Posts: 10
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Mavic Clone STL Files Version 4.1 Naza
« Reply #151 on: March 25, 2018, 03:55:41 PM »
hi having a problem with the front right leg, I always get an error stating that the part is "not manifold".
has anyone else had this error, and has a work around.

back legs and left front have so far printed well.77

 Neil

Offline Popol974

  • Drinks Maker
  • *
  • Posts: 4
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic Clone STL Files Version 4.1 Naza
« Reply #152 on: May 22, 2018, 08:15:30 PM »
Hello,

is someone has a config based on black widow 2204 and naza-m V2 please?

I calibrate the esc with the channel 3 of a traditionnal rx and i think its good because the trottle is linear and smooth.

But when i put my turnigy ia6c by s-bus with the naza-m V2 : after arming, the 4 motors run low and the trottle do nothing until the middle and after the middle start brutaly the motors. the motors continue to increase speed even if i dont move more the trottle...

i try to fly...the drone come very fast up and i put down the trottle he falls very quick...so its impossible to fly correctly and smooth.

I am in GPS mode.

Thanks by advance

Offline skyman

  • Drinks Maker
  • *
  • Posts: 10
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Mavic Clone STL Files Version 4.1 Naza
« Reply #153 on: May 23, 2018, 07:12:15 PM »
Hi, I've not got that far yet. but i have read that taking off in GPS mode is not the best and can be a problem.

have you tried manual mode or alt hold?

Offline Popol974

  • Drinks Maker
  • *
  • Posts: 4
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic Clone STL Files Version 4.1 Naza
« Reply #154 on: May 23, 2018, 07:37:36 PM »
hello,

thanks for your reply,

yes i have try in atti it seems to be better...

Why taking off in GPS is a problem? can you give me the link where you read this please?

Offline skyman

  • Drinks Maker
  • *
  • Posts: 10
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Mavic Clone STL Files Version 4.1 Naza
« Reply #155 on: May 23, 2018, 10:07:48 PM »
Hi, Sorry but I've been looking at forums and YouTube so much, that I can't remember where I read it.
 

Offline Millerboy3

  • Drinks Maker
  • *
  • Posts: 6
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic Clone STL Files Version 4.1 Naza
« Reply #156 on: May 31, 2018, 11:07:44 PM »
Hi, Sorry but I've been looking at forums and YouTube so much, that I can't remember where I read it.

Its actually stated in the Naza manual as well....

Offline finn.bennet

  • Drinks Maker
  • *
  • Posts: 2
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic Clone STL Files Version 4.1 Naza
« Reply #157 on: June 06, 2018, 02:46:13 PM »
Hello,

I am new to this forum and planning to 3d-print this Mavic Clone (Naza version). Very nice work btw!

I want to use some DJI 2312 motors I have laying around in combination with this lipo: https://hobbyking.com/de_de/turnigy-graphene-4000mah-3s-15c-w-xt60.html

Now the question is whether I should use the DJI 9450 9.4" Props and scale the mavic up or whether I should get some new smaller Props not scaling up the model. For example Graupner e-props 8x5.

Thanks by advance.
Finn

Offline Millerboy3

  • Drinks Maker
  • *
  • Posts: 6
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic Clone STL Files Version 4.1 Naza
« Reply #158 on: June 06, 2018, 04:28:14 PM »
Hello,

I am new to this forum and planning to 3d-print this Mavic Clone (Naza version). Very nice work btw!

I want to use some DJI 2312 motors I have laying around in combination with this lipo: https://hobbyking.com/de_de/turnigy-graphene-4000mah-3s-15c-w-xt60.html

Now the question is whether I should use the DJI 9450 9.4" Props and scale the mavic up or whether I should get some new smaller Props not scaling up the model. For example Graupner e-props 8x5.

Thanks by advance.
Finn

You don't need to scale it up.  I use standard 9450 dji props on mine with 2212 920kv motors with no issues.