Author Topic: Mavic build - Mkc2  (Read 7411 times)

Offline patrick57

  • Drinks Maker
  • *
  • Posts: 25
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #45 on: July 08, 2018, 05:27:22 PM »
very good
 :) :) :)

Offline Mkc2

  • Junior Designer
  • **
  • Posts: 71
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #46 on: July 09, 2018, 02:31:20 PM »
Well after mounting the GPS in the back and fitting the Runcam split back on, It still has interference and needs to be clear of about 10 inches away.
Even the copper tape seems to make no difference.  >:(

Offline patrick57

  • Drinks Maker
  • *
  • Posts: 25
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #47 on: July 09, 2018, 06:36:50 PM »
We should try to lift the gps with the pylon, to see if it works. I'm afraid to finish mine.
 :-[ :-[ :'( :'(

Offline ronson

  • Elite DIY RC Supporter
  • Junior Designer
  • ******
  • Posts: 51
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #48 on: July 09, 2018, 10:35:30 PM »
Nice flight video and nice work overall...

Thats really odd that the copper tape didi't help much at all..
Maybe more layers of copper would help?!


Offline Mkc2

  • Junior Designer
  • **
  • Posts: 71
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #49 on: July 09, 2018, 10:48:40 PM »
Nice flight video and nice work overall...

Thats really odd that the copper tape didi't help much at all..
Maybe more layers of copper would help?!

I think its the runcam, its to strong with interference and worse then the gopro.
I will give the Mobius camera and try.

Offline Mkc2

  • Junior Designer
  • **
  • Posts: 71
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #50 on: July 10, 2018, 01:51:56 PM »
Well I tried 3 cameras and no luck with the interference.
I gave up and will set up the camera and gimbal onto my tricopter which has plenty off room ( no gps )  :)
At least with out all that extra gear I can still have my 15 min flight time :)

Offline patrick57

  • Drinks Maker
  • *
  • Posts: 25
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #51 on: July 10, 2018, 06:30:42 PM »
 if it takes 10 inches gap between the gps and the cardigan, it will be difficult for me too, I do not know how!
:-\ :-[ ???

Offline skyman

  • Drinks Maker
  • *
  • Posts: 10
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #52 on: July 10, 2018, 07:49:34 PM »
try putting copper foil around the camera and a wire link to the battery -neg. screen the source and not the receiver. you want to ground the foil so the signal has some where to go.

Offline patrick57

  • Drinks Maker
  • *
  • Posts: 25
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #53 on: July 11, 2018, 10:59:05 AM »
Thank you for the advice, I will try.
 :) :) :)

Offline AlJD

  • Drinks Maker
  • *
  • Posts: 1
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #54 on: July 30, 2018, 06:44:38 PM »
Hello,

I solved a gimbal interference problem by using twisted wires to power the gimbal motors, this is a simple solution that might work.
Of course I assume you did a mag calibration of the Naza after installing the gimbal.

Al

Offline patrick57

  • Drinks Maker
  • *
  • Posts: 25
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #55 on: July 30, 2018, 07:29:28 PM »
Hello, this is good news, soon a video please;

Offline Mkc2

  • Junior Designer
  • **
  • Posts: 71
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #56 on: July 30, 2018, 10:50:19 PM »
The interferance I got was from the cameras, no gimbal motors were fitted as you can see in the video.

Offline nogod4me

  • Drinks Maker
  • *
  • Posts: 9
  • Karma: +0/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #57 on: July 31, 2018, 12:45:04 PM »
Hello from Russia!
Man, you've done a huge beautiful work! You impressed me try like you! ;)
Would you please share you modified legs and top parts STL files? My email is nogod4me@yandex.com
Thanks a lot!

Offline Mkc2

  • Junior Designer
  • **
  • Posts: 71
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #58 on: August 01, 2018, 03:18:02 AM »
Stl file for back legs
« Last Edit: August 01, 2018, 03:30:37 AM by Mkc2 »

Offline Mkc2

  • Junior Designer
  • **
  • Posts: 71
  • Karma: +1/-0
  • rookie
    • View Profile
Re: Mavic build - Mkc2
« Reply #59 on: August 01, 2018, 03:25:47 AM »
Stl file for front left