This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - triafgg
1
« on: January 02, 2018, 12:23:28 AM »
Hi Davide
It's been a long time but I think I scaled it all up 112 percent but on the arms only scaled up the Z axis to maintain the fit between top and bottom components and also the X or Y so that the motors still lined up, can't remember which. To test just scale up X or Y and check that the motor holes stay correct and leave at 100% the one that keeps it right. The motor mount goes a little oval as only scaling in one direction but that doesn't matter. Actually, thinking about the oval shape, I think the X stays at 100%
2
« on: August 23, 2017, 12:14:20 AM »
Mine's 925g with battery 15 min flight time.
3
« on: August 05, 2017, 10:47:55 AM »
Yes that should be fine.
4
« on: July 30, 2017, 11:26:38 AM »
Hi Kondratev
I have already answered your question in post #85 regarding power.
5
« on: July 29, 2017, 04:25:26 PM »
That's the NAZA M way but for F3 or any betaflight/cleanflight you will need
4 2
3 1
1 CW 2 CCW 4 CW 3 CCW
6
« on: July 18, 2017, 07:36:03 PM »
I did the body at 30% with 2 walls, arms at 50%. The arms will break at that if you crash so more incentive not to crash
7
« on: July 17, 2017, 09:48:55 AM »
Hi
Mine is at 850g with everything fitted. Naza V2 Black Widow motors with integrated ESC. 3000Mah battery
Flight time about 17 mins with 8" props.
8
« on: June 05, 2017, 03:36:43 PM »
Hi Moschi
M3 4x40mm and 8x28mm is what you will need. They can be cut down a little depending on the depth of the nuts you use.
9
« on: May 31, 2017, 09:48:27 PM »
Hi
Here are my gain settings. I put them on X1 so that I can adjustin flight and this was nice and stable but yours will be different. I mapped Ch5 to a rotary switch and this is X1 in the Naza.
10
« on: May 23, 2017, 05:39:22 PM »
If you arm it and raise the throttle a bit but not enough to take off then disarm the props should all stop near enough together. If one takes longer to stop then it will have been running faster so you would need to calibrate. Also if you do a punch out and it goes off to one side instead of straight up then there will be an unbalance. It is easy to do in cleanflight with a nase32 but not found out how to do on a Naza. Maybe it isn't required in Naza because it's more intelligent. In cleanflight you power up with full throttle(PROPS OFF) and then drop the throttle to minimum and it's done. Maybe that principle also works with Naza, never tried as don't have much experience with them, this is my first Naza board.
11
« on: May 23, 2017, 11:36:45 AM »
Yes a Naze32. Try if first, you may not need to calibrate.
12
« on: May 23, 2017, 10:46:02 AM »
Hi Kondratev
The ESC from motor 1 goes into M1, motor 2 to M2 etc. You just need the white wire from the ESC, you can cut off the black, but not too short in case you need to calibrate the ESCs which you can't do with the Naza as far as I know. I just hook up a cheap naze board and do it with BLHeli suite but you need the white and black for that and would need to temporarily reconnect the black.
13
« on: May 23, 2017, 08:31:21 AM »
I didn't mod any files for mine, just scaled it down.
14
« on: May 17, 2017, 08:18:23 AM »
There is a split version so you can print the middle in two pieces. Actually I use this anyway as you can replace either the front or back legs without taking the whole thing apart.
15
« on: May 15, 2017, 11:47:23 PM »
You need to scale Z the same as the rest so that the arms are thick enough to fit between the base and the top cover, Y scales the length of the arms so optional and X the width. I scaled mine in Y and Z which left the holes at 16/19mm(X axis). The motor base is slightly egg shaped but it doesn't notice and the motors fit fine. Not scaling Y would keep them the same shape.
|