Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Hoochster

Pages: [1] 2 3 ... 8
1
3d Printed Mavic Clone / Re: Mavic Clone STL Files Version 4.1 Naza
« on: August 21, 2017, 08:46:21 PM »
Hi Zaghir,

There is a list somewhere but they are all M3 screws, I just got a selection and just pick from them so didn't really measure them. Do a search and they should come up.

Thanks,

Steve

Been away for quite awhile, and need to get back to it, just been way too busy haha.  But assuming these links still work, or even if they don't.  the sizes should suffice for ya.

7 of 3mm x 25mm (top / front legs / rear legs / back battery mount)
http://www.ebay.com/itm/152435299137?_trksid=p2060353.m2749.l2649&var=451739290180&ssPageName=STRK%3AMEBIDX%3AIT

4 of 3mm x 40mm (body) - Cost the most due to shipping
http://www.ebay.com/itm/252799128128?_trksid=p2060353.m2749.l2649&var=551804678837&ssPageName=STRK%3AMEBIDX%3AIT

1 of 3mm x 20mm (front battery mount)
http://www.ebay.com/itm/152435299137?_trksid=p2060353.m2749.l2649&var=451739290180&ssPageName=STRK%3AMEBIDX%3AIT

Lock Nuts
http://www.ebay.com/itm/401045509185?_trksid=p2060353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

2
Mavic Build Diaries / Re: Mavic Build - Kondratev
« on: May 08, 2017, 01:23:38 PM »
Just like in this pic attached, it is kind of confusing I know.  The actual motor spin is the opposite of what is labelled on the motor itself.  What that label is in reference to is the nut per say I guess.  In how it tightens down while the motor spins.  That still isn't a good explanation.  But what I am trying to say is, a CW motor spins CCW and the Nut will tighten CW to keep from falling off.  And same for a CCW motor, it will spin CW and the nut tightens CCW to keep from falling off while it spins.  So as per that picture for a NAZA Build:

The top right M1 Motor needs to be a CW, top left needs to be a CCW, bottom left CW and finally bottom right CCW.

Hope that helps.

3
3d Printed Mavic Clone / Re: Mavic Clone STL Files Version 4.1 Naza
« on: May 05, 2017, 02:08:47 PM »
I plan to try and modify to make the round one, I just haven't had the time just yet.  That one will be more of a challenge for me, but I will DO IT! :)  Out of town all weekend.  Will try and tackle it after the weekend.

4
3d Printed Mavic Clone / Re: Mavic Clone STL Files Version 4.1 Naza
« on: May 05, 2017, 07:19:33 AM »
Fatboyjon, no problem, ya, I am lucky enough to work from home most of the time.  You don't need the small black cable, but if you ran them and want to hook it up, it is top.  The white signal wire goes towards the bottom. 

Triafgg, it is for the v1.5 Naza GPS, it is still a square GPS, it is just a much larger GPS than what Steve was using with his stock build.  So I had to enlarge the nose piece to fit it.  So it looks very similar, just the outside and inside cutout is larger.  But thanks for questioning just in case! :)  Pics below to compare:

Left is stock, and right is my mod:








Not a perfect job, but hey it was my first mod! :) 

5
3d Printed Mavic Clone / Re: Mavic Clone STL Files Version 4.1 Naza
« on: May 04, 2017, 01:36:14 AM »
Sorry, got stuck in the office for most of the day, TERRIBLE, used to working from home haha.  Then almost forgot to send this heh.  Here is the v1.5 STL I modified.  Again, it is a poor mans mod, I know it could be done much better, but hey it does fit like a glove.  So whatever works.  Till Steve can make us a better one.  Hope it helps.  Will try and make the v3 one sometime.

6
3d Printed Mavic Clone / Re: Mavic Clone STL Files Version 4.1 Naza
« on: May 03, 2017, 05:57:11 PM »
Ya, I managed to make a ROUGH mod to the 1.5 Naza GPS heh, nowhere near as nice as what CDR would do mind you but would be happy to share it till he makes one heh.  I am not at home at the moment to get the file to ya though.  I hope to be home in a couple hours or so hopefully and will upload it.  It isn't pretty but it worked just fine.  I didn't make one yet for the v3 model, but need to, cuz a friend of mine has that plus I bought just the GPS as well.  Hopefully CDR can make a proper one for each of them, mine were pretty rough being as I don't truly know how to mod files yet heh, but I managed to do some pushing and pulling! :)

7
Mavic Build Diaries / Re: Mavic Build - Kondratev
« on: April 30, 2017, 07:25:11 PM »
Ya, I had ordered a kit of connectors for something I was working on awhile back, so worked out well:

https://www.amazon.com/gp/product/B012EOO9Q0/ref=oh_aui_search_detailpage?ie=UTF8&psc=1


8
Mavic Build Diaries / Re: Mavic Build - Kondratev
« on: April 30, 2017, 07:08:32 PM »
You shouldn't need the black wire, just the white.  What I actually did was like CDR did use a pin or something to get the wire out and I snipped the black wire.  I had to extend my white wires to get them to the length I wanted, then I got some connectors I had, and used a 4-way block and put all 4 of the white wires in that block to plug into the flight controller. 



9
3d Printed Mavic Clone / Re: Naza Build just flips?
« on: April 30, 2017, 07:00:45 PM »
I get liftoff with the Mavic Clones, but they are very wobbly, I think they are just cheaply made.  I don't know if the real Mavic ones are stiffer and will hold up better.  But obviously will probably cost more.  But honestly haven't looked.  I have some regular props on order to confirm that fixes my issue.  But I feel that it will.  But just with the mavic clones on the heli I feel wobble in them if I try and wiggle them manually.  So you can try and tighten them up a little and see if that helps, but I doubt it will help much.  There might be some others out there no doubt made a bit better.

10
3d Printed Mavic Clone / Re: Naza Build just flips?
« on: April 28, 2017, 11:12:52 PM »
Well it ATTEMPTS to do better with them flipped now.  But once it gets up in the air it tries to flip again.  BUT now, it is doing what I am guessing is what you were experiencing with those cheap props Triafgg.  So maybe the cheap props just can't cut it.  They do seem pretty wobbly.  But it does now at least try and get up in the air for a few seconds now before it freaks out.  So that must have been it.  Then it dies.  So I will have to get me some props on order.  I have some 6x4.5's but those are prob a tad too short heh.  The only other size I have is 10x4.5's heh.  What size did you order?

11
3d Printed Mavic Clone / Re: Naza Build just flips?
« on: April 28, 2017, 10:13:08 PM »
Nah, only 4:15 p.m. right now but rainy day.  Had to run daughter somewhere.  So will have to try and do aa quick teat when I get back before I have to goto a other daughters dance thing haha.  It never ends lol.  Hopefully 2 front motors swapped can cause that just seems like it would swap the side it is flipping towards.

12
3d Printed Mavic Clone / Re: Naza Build just flips?
« on: April 28, 2017, 09:55:49 PM »
I might have had M1 and M2 reversed, putting it back together now, so will see if that made a difference. 

13
3d Printed Mavic Clone / Re: Naza Build just flips?
« on: April 28, 2017, 09:47:42 PM »
Ya, will have to take it apart and check it, it is quite possible I hooked it up wrong, but I am using a 4-way connector hooked to the FC.  I thought I triple checked I had them in order, but I did re-do the dang wires so many times to get them shoved in there properly so maybe I hooked them up wrong the last time haha.  I'll let ya know.

14
3d Printed Mavic Clone / Re: Naza Build just flips?
« on: April 28, 2017, 08:53:26 PM »
Ya, the compass calibration, I have, but maybe I need to do it a few times, I dunno.  I did have an issue when I first setup where it didn't seem to want to initialize till I did some download/update to the IMU manually or something.  Then it all the sudden seemed to start working.  Dunno.  So maybe I need to do that again as well.  Maybe that didn't take properly. 

15
3d Printed Mavic Clone / Re: Naza Build just flips?
« on: April 28, 2017, 08:49:19 PM »
Ya, only wired the signal wire to the Flight controller to the Naza.  And combined the power/grounds.  They all spin the proper direction.  Just it tries to flip over on lift off.  When this has happened to me on previous flight controllers in the past it was a buggy PID Controller.  But don't think I can adjust that in the Naza like that heh.  So I assume it is something else.  Surely something simple.  All else appears to be setup ok.  It is a very tight fit heh.  But that is probably just me.

Pages: [1] 2 3 ... 8