Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - uros2002

Pages: [1]
1
Hello,

I'm trying to connect Omnibus f4 pro v2 controller.
I've connected Doha now
Frsky xm + - SBUS, 5v and GND
GPS BN-280 - UART6 - rx6, tx6, 5v and GND
Servo gimbal - pwm5 and pwm6
LED - on the other side of the J1 - 5V, GND and LED
This is bothering me now
Sonar HC -SR 04 - 5V, GND, (UART6 - SCL and SDA) if I understood it well

2
Mavic Build Diaries / Re: Mavic Build from Serbia
« on: February 06, 2019, 08:04:08 PM »
Hi, can you help me.
What is the diameter of the central hole for the motor shaft..........

Hello! 3mm

Thanks for your reply.
PWM5 and PWM6 I would use Servo_Gimbal

Can it connect this way and where to connect the sonar?

4
Mavic Build Diaries / Re: Mavic Build from Serbia
« on: February 02, 2019, 02:13:19 PM »
Hello,

I finished printing and tried to fit parts. He's got a little bit of finishing, but he's OK.
I was planning these engines to fit.

Where should I put this part from last picture?

5
Mavic Build Diaries / Re: Mavic Build from Serbia
« on: January 30, 2019, 06:46:50 PM »
Now I checked this by the image controller I have



It's a clone version.
Ordered from this site
https://www.aliexpress.com/item/betaflight-F4-Pro-V3-Flight-Controller-Board-Built-in-Barometer-OSD-TF-Slot-For-FPV-Quadcopter/32885245893.html?spm=a2g0s.9042311.0.0.6ab04c4dDSe22L

Can someone tell me which version of FW inav or Betaflight to install on FC

6
Mavic Build Diaries / Re: Mavic Build from Serbia
« on: January 29, 2019, 07:45:20 PM »
Continuation of works

8
Mavic Build Diaries / Re: Mavic Build from Serbia
« on: January 28, 2019, 09:10:55 PM »
This is the FC that I have

I do not understand too much about this, so I need help.

9
Mavic Build Diaries / Re: Mavic Build from Serbia
« on: January 28, 2019, 08:44:20 PM »
I can not find how to connect
Omnibus F4 V3 pro

+ sonar HC - SR04
+ GPS BN220 - OK
+ Led RGB for ARM, GPS lock, Battery OK

10
Mavic Build Diaries / Re: Mavic Build from Serbia
« on: January 28, 2019, 07:27:36 PM »
Thanks for the STL file,


I use F4 V3 FC, Sonar HC-SR04, Racerstar BR2212 1000KV, EMAX BLHELI 20A , RunCam swift and TS5828L + Pagoda
I would use the BN-220 GPS with Dimension: 22mm * 20mm * 6mm

I'll try to modify an existing file, or use the one you sent me.

11
Mavic Build Diaries / Re: Mavic Build from Serbia
« on: January 28, 2019, 11:48:46 AM »
Did someone work in the front cover to install the GPS antenna and the battery indicator in the back cover?

12
Mavic Build Diaries / Re: Mavic Build from Serbia
« on: January 28, 2019, 10:36:41 AM »
OK thank you

13
Mavic Build Diaries / Re: Mavic Build from Serbia
« on: January 28, 2019, 10:22:36 AM »
Download the F3 plan.
When I'm done, I'll see if there will be some modifications in terms of GPS, LED, Battery Indicators, .....

If it can only answer the question about infil.

14
Mavic Build Diaries / Mavic Build from Serbia
« on: January 27, 2019, 10:35:05 PM »
Greetings from Serbia,

My name is Dejan and I live in Serbia.

I looked at this DJ Mavic for a long time and finally decided to try to print one.
I downloaded parts and I started to print the first part.
1 - Base Middle - 30% Infil PLA
Can you tell me more about the printing procedure that infil and similar.
I plan for 70% infil for arms

Thanks in advance Dejan

Pages: [1]