Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Awdhoot

Pages: [1] 2
1
Mavic Build Diaries / Closest to original mavic i can get ... :o
« on: February 15, 2021, 06:48:57 AM »
I started this project 2 years back , and now finally its looking like something .... ;D

Build :

1) mavic pro naza 4.1 design
2) dji naza m lite upgraded to V2
3) original mavic pro motors
4) mavic pro low noise props
5) Favourite littlebee spring 30a ( blheli s)
6) flysky fsi6
7) HBP power 2200 mah 3s lipo

Flight time:

on 2200 mah lipo first level protection activated after 8 mins (11 volt load 11.5 no load )
10 mins of total flight time till second level protection activates and lands the drone (10 volt load and 10.5 noload )

issues I faced :

1) motor mounts - dji uses its own 3 screw mount for which the arms need to be modified , i posted those modified arms in this forum - http://diyrc.co.uk/mavic-build-diaries/modified-arms-for-dji-mavic-orignel-motors-(finally-tested-)/msg6454/?topicseen#new  - use 9 mm m2.5 screws if you got longer ones either use spacer or cut screws

2) naza gps size issue -  i am using original naza gps which have round pcb for that you need to use modified round nose -http://diyrc.co.uk/3rd-party-parts-12/new-nose-for-(round)-naza-gps-(v3)/msg4078/#msg4078

3) fsi6a rx pin header problem - using servo pins in this build is terribly hard task so just soldered to the back of the signal pins

4) naza led module not available or too big for your taste - i got my naza m lite used so it came with naza v1 power and led module (combined ) which you have already guessed is terrible to see from outside so i just installed a 5050 pcb which is very slim in profile , https://www.amazon.in/Robocraze-Arduino-Colour-Module-Project/dp/B07NDSZ95Y (purchase the version without resisters )  connections- open nazza v1 led module you need to solder 3 wires from it to (1) to gnd (2) to red (3) to green of 5050 led pcb

5) where to put esc - this wont be a huge issue if you get 4 in 1 in first place but if you got escs like me what you can do is arrange the escs like a 4 in one with layers of insulation tape of course its not so much heat efficient but can save some space and place it in backside of naza

6) usb interface for naza v1 pmu - naza v1 have usb port on pmu which gets very hard too reach sometimes so my solution was to find slimmest micro usb cable with smallest head and cut maybe 5 cm from it and solder male headers to it making my own usb extension and soldered female headers to remaining cable

7) programing esc - due to some power limitation in blheli escs your quad can shake a lot so took a advise from youtuber to turn it off  ( low rpm power protect ) -
&pbjreload=101 refer first comment

8) naza programing
- by default naza assist uses f450 gains to all the configs when you choose quad x in naza setup but due to fact that rear arms are lower then front arms it causes issues particularly speaking pitching very fast forward without even touching any sticks

found the working gains in this same forum ( cant thank him enough )  http://diyrc.co.uk/3d-printed-mavic-clone/it-fly's-sort-of/msg6541/?topicseen#new 

use 108 99 100 100 config

9) more space - using optimized upper parts can certainly make your life easy - http://diyrc.co.uk/3rd-party-parts-12/optimized-upper-parts-for-more-space/

some of my mods :

1 ) risers for arms and belly ( clip on pressure fit no need to glue or screw ) - http://diyrc.co.uk/3rd-party-parts-12/front-leg-riser-belly-riser-back-leg-locks-long-catch-for-top-parts/

2) modified legs for mavic pro motors - http://diyrc.co.uk/mavic-build-diaries/modified-arms-for-dji-mavic-orignel-motors-(finally-tested-)/msg6454/?topicseen#new

note : - coloring is still left and drone was going crezy at the beginning so don't judge me on those dirt marks  ;D

2
3d Printed Mavic Clone / Re: It Fly's sort of....
« on: February 15, 2021, 03:48:13 AM »
i have come way back from future just to say tank you , i was really started to get annoyed over my quad drifting and wasn't that much of a expert so couldn't set gains myself , your gains made my quad rock stable ... lot of thanks

3
made some parts to fit mavic(naza )

1) Rear leg locks - fits out of bed
2) front leg risers - need little bit sanding to fit in the slit closest to motor
3) front belly riser - if you don't wanna add leg risers alternatively you can attach this to front side ( where mavic name is written ) with 3 screws and brass inserts
4) catch - long catch to go with new upgraded top parts posted in third party parts

4
plungers are exactly the same i only changed motor mount

5
3d Printed Mavic Clone / Re: List of finished projects?
« on: August 18, 2020, 08:26:08 AM »
it would be great if someone can share how they fitted esc and all stuff

6
can anyone share how they are fitting esc and other ele in frame
i have fevourite spring blheli s elcs (not 4 in one )

7
M 2.5 (6.5mm) hex heads

8
Mavic Build Diaries / Re: The Frankenstein build
« on: May 24, 2020, 03:30:20 PM »
are those orignal mavic arms ??


9
 so finally tested the arms for dji mavic motors

here are sample photos



special thanks to "lezabour" for testing the designs

i attached zip file with 4 modified legs below ...

10
found working screw; print is working :)
i'm now printing the full arm you provide to test

thanks

cool..... :D :D   i will do other 3 at night can you send me some pics so that i can have idea about motor reses is enough or not

11
hey,
cool thanks for your reply
i have the motors, and the 3d printer ;) i will now cut in tinkercad and testprint,
will let you know today ;)

thanks for your help

PS: i cant see the pictures in the post you are refering too, but i can download the stl, so everything is good


after printing lemme know if it works  ;D

12
Hi guys
Any news on modifying arms for original motors ?
I also have the original motors and propellers that i would love to you

Thanks ;)

http://diyrc.co.uk/mavic-videos/arms-for-dji-mavic-orignal-motors/msg6283/#msg6283

13
Hi guys
Any news on modifying arms for original motors ?
I also have the original motors and propellers that i would love to you

Thanks ;)

i had uploaded designs for modified arm with refrance to above image because as of now i don't have motors
you can try them and let me know your feedback so i can update and upload full design

(just print motormount part cut rest of arm in 3d builder or tinkercad ) and test fit motor and lemme know ..... 

14
Mavic Videos / Arms for DJI mavic orignal motors
« on: March 24, 2020, 09:09:30 AM »
some days ago a member posted idea about using orignal mavic motor for our printed one
so i wnated to order some for myself aswell
those motors need some custom mounting hole diff from regular 2212 motors

so until my my motors get to me i want to make those arms
so searched some dimentions online and some from previous post i modified cad files provided by CDRskull

but sadly i dont have anything to test fit

so am uploading those files here if anyone have those motors please testfit those in this arm
if anything is wrong please leeme know i will modify those again

also if anyone have those motors handy it would be great if you provide me dimentions








happy flying ;D

15
Am also planing to buy from Ali I will give it a shot can you give me exact dimensions I will make it and will share it

Pages: [1] 2