Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Kananga

Pages: [1] 2 3 ... 10
1
As you offered via pm will be fine Thank you.
You say you designed and drew it, at best you drew it but it's my design.

If it's removed it's matter over.

2
Still copied then, still my design, still no permission given, still no credit given.
Funny yours have same error mine did, same size angle mine did, same size flatter diameters mine did.
I'll let thingiverse decide, I'm never posting stls anywhere again.

3
How come it's exactally the same file as the one i uploaded here then.

I'm deadly serious, I believe you've taken my prop adaptor files I kindly drew out and uploaded to here and you've posted them on thingiverse under your name.

There are measurements on those adaptors that I made up and those measurements are on those designs.

4
I've reported it to thingiverse,  i hate theives. Ill not be helping him again.

5
3d Printed Inspire Clone / Re: Camera systems
« on: May 06, 2019, 03:07:50 PM »
I've shelved mine to be honest I lost interest and started making foam planes. I'll get back to it at some point.

The problem with 4k fpv would be latency, for fpv you don't need crystal clear pictures if you've got a means to record from a decent camera and have a separate fpv camera then your getting the best of both worlds. I liked the idea of the split for it's quality of recorded video and the low latency of the built in fpv which is in itself a good picture.

For 4k fpv I'm not aware of any ready to go systems but doesn't mean there aren't any of course, a lot of people use a go pro to record and have a cheap fpv set up for lining the shots up.
I've read a lot of bad reports about the go pro video transmitting system but don't know how it works, Im thinking it works on WiFi which limits it somewhat in range but I also believe it has big latency issues.

If your ok with a separate fpv camera or guesitmating your shots somthing like the go pro wouldn't need wires.

The dji cameras are like the split, the bit on the gimbal is just the lens and image sensor, the actual electronics are built into the main boards. As far as I know no-one has interfaced with either their cameras or their gimbals. One day I might achieve the gimbal side but for now I'm going to stick with my split for the camera.

Keep us updated what you decide.


6
3d Printed Inspire Clone / Re: Camera systems
« on: May 06, 2019, 11:50:24 AM »
Loads of cameras,
I've been using a runcam split v2, excellent camera.


7
Looks like you've copied my prop adaptors there :(

8
Mavic Build Diaries / Re: F4 v2 build 4.1 with camera
« on: April 15, 2019, 10:02:20 PM »
Go to the top of the screen and there's a tab called downloads.
Click on downloads, click on the next bit then the list of models opens.
Choose the model you want and click, then choose the model suitable for the fc you're using.

9
Image through receiver won't be great but the footage on your memory card will be, use the fpv to line your shots up but don't rely on recording the transmitted signal.

10
3d Printed Mavic Clone / Re: Mavic Clone STL Files Version 4.1 Naza
« on: March 31, 2019, 01:37:45 PM »
Click downloads, click magic downloads, top of the list it says cad files ;)

11
Quote from: BerniApple
i really can't make it works... the sonar icon on iNAV is red. how did you active it on the "configuration" and "ports" tab

Looking for a simple solution online for you I notice lots of blogs saying don't use this module. Unless you're flying 3 foot above concrete it's pretty useless due to noise. I know it's the recommended module but I wouldn't worry too much if you don't use it. If you want to get it working correctly you can look on the net for the arduino projects people have made that allow your fc to use the data properly otherwise, as I say,  it's reportedly very hit and miss.

I have the same module but after reading what I just have I'm going to try mine once and if it doesn't work I'll leave it off.

Other than that lama might be able to help you get it working as is.

12
Lama, from what I understand your correct, the advantage of plugging your camera through your fc at the moment is to configure/alter the settings of the camera through your transmitter.
You should however still get a picture I think.

To get osd you do need a separate osd board such as https://m.banggood.com/MICRO-MinimOSD-Minim-OSD-Mini-OSD-W-KV-Team-MOD-For-Naze32-Flight-Controller-p-990556.html?rmmds=search which can be run through your fc to add the additional osd.

Maybe you have to assign uart1 to be a video channel in inav or maybe toggle a switch, I'm sorry but I'm not sure why you're not getting a picture.

13
3d Printed Mavic Clone / Re: Mavic Clone STL Files Version 4.1 Naza
« on: March 30, 2019, 11:17:07 PM »
Not really but it is self explanatory. Take a look through the various build logs for pointers, start your own build log for help.
I've boxed mine up for now but once my printer is back up and running I'll finish it off but I still drop by the forums.
There are some threads with hardware lists and there are assembly models in the downloads
When I get up and running again I'll post up a hardware list.

14
If you print a new lid with 20% infill you should be able to Dremel the inside out quite easily.

15
Congratulations mate, looking good.
The original files are in download section but they won't load in my cad, I can hollow the original out a few mm for you if you want?

Pages: [1] 2 3 ... 10